Hi All,
I’m shortly due to pick up my used Macan S II, however, as the car was originally specced with the model designation deletion option, I’m considering to fit the rear Macan S badge.
As I’m not sure of the exact placement of this badge, would any Macan S II owner be so kind as to send me the following measurements, in millimetres, in relation to the attached photo:-
A - from the edge of the O to the edge of the M
B - from the edge of the H to the edge of the S
C - from the bottom of the Macan lettering to the bottom edge of the boot lid
D - from the bottom of the plastic trim to the top of the M, and from the boot crease line to the top of the M
E - from the bottom of the plastic trim to the top of the S, and from the boot crease line to the top of the S
F - from the boot crease line to the top of the a & c letters
G - from the bottom of the S to the bottom edge of the boot lid
Many thanks,
Allan
Macan S II rear badge placement measurements
Steve
2020 GTS in Sapphire Blue
(sold) 2017 SD in Rhodium Silver
2020 GTS in Sapphire Blue
(sold) 2017 SD in Rhodium Silver
Thanks for this link, but none of them show the measurements I’ve asked for, and some even relate to the Mk1 Macan, which is not the same as a Mk2 boot lid.SAC1 wrote: ↑Fri Nov 13, 2020 1:52 pm
As already discussed on this Forum.....search.php?keywords=lettering+template
Allan
2023 Macan S in Crayon
2023 Macan S in Crayon
-
- Posts: 984
- Joined: Sat Aug 20, 2016 9:11 pm
Thanks for this link, but I’m certainly not paying $135 plus postage for a template!!CharlesElliott wrote: ↑Sat Nov 14, 2020 9:54 am https://www.suncoastparts.com/product/SKUTEMPG295B.html
Surely there must be a forum member with a Macan S II who has the reward badge who can kindly take the measurements for me??
Allan
2023 Macan S in Crayon
2023 Macan S in Crayon
It’s not difficult to set up, take a look at the photo below. For the vertical the centre of any badge size/configuration whether it be the example, the S, GTS etc) is always centred to the “S” in PORSCHE, which is also the centre of the wiper rotor and the bottom skirt strengthener. For the horizontal, the bottom of the lettering lines up with the lower fold of the tail gate lamp recess. You can set this up with just masking tape, a non permanent fine line marker and a suitable spirit level. Trial place it and double check alongside a few decent photo examples before committing.AllanG wrote: ↑Sat Nov 14, 2020 10:03 amThanks for this link, but I’m certainly not paying $135 plus postage for a template!!CharlesElliott wrote: ↑Sat Nov 14, 2020 9:54 am https://www.suncoastparts.com/product/SKUTEMPG295B.html
Surely there must be a forum member with a Macan S II who has the reward badge who can kindly take the measurements for me??
p.s the example is not my car
Previous Porsche’s
2008. 987 Boxster S Sport basalt
2012. 991 Carrera S aqua
2016. Macan Turbo volcano
Current
2020. Macan GTS crayon
2024. Macan GTS gentian. Delivery update mid May https://configurator.porsche.com/porsche-code/PR8H7WC6
2008. 987 Boxster S Sport basalt
2012. 991 Carrera S aqua
2016. Macan Turbo volcano
Current
2020. Macan GTS crayon
2024. Macan GTS gentian. Delivery update mid May https://configurator.porsche.com/porsche-code/PR8H7WC6
-
- Similar Topics
- Replies
- Views
- Last post
-
- 12 Replies
- 3499 Views
-
Last post by PowerMalc
-
- 3 Replies
- 951 Views
-
Last post by Skyway
-
- 2 Replies
- 2173 Views
-
Last post by pmg
-
- 13 Replies
- 3082 Views
-
Last post by RGS
-
- 9 Replies
- 3643 Views
-
Last post by Chris skiz